圖片網址很長,建議看網頁版
https://www.ptt.cc/bbs/PC_Shopping/M.1473755441.A.BBA.html
配備大致如下
處理器 Broadwell-E i7-6850K
散熱器 Thermalright SilverArrow IB-E Extreme
主機板 EVGA X99 FTW K
記憶體 Crucial DDR4-2666 Ballistix Tactica 8G*4 共32G
系統碟 OCZ RD400 256G
顯示卡 PowerColor AXRX 480 8GBD5-3DH/OC
電供 CORSAIR RM850i
螢幕 acer XZ271 x3台
市售機殼的配置我怎麼看都不滿意,只好拿2020鋁條自己做一個
我希望 硬碟抽取槽/光碟機/各種資訊面板 在螢幕下方橫向展開
拿免費的LibreCAD進行粗略規劃 (沒學過製圖只能亂畫一通)
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/PC_zpsqe3x3j4m.png
不是很精準的設計圖,只是各零件的相對位置
考慮走線路徑之後,決定用主機板擺右邊的配置
淘寶訂製的 "2020歐標鋁型材" ,溝槽一堆碎屑待清理
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09136_zpsdebigd9d.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09145_zpseppj1hx8.jpg
全部選用內置型的L型連接件,外觀比較簡潔,缺點是事後很難調整
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09158_zpsnvi1vg3m.jpg
我拿電鑽+氣泡紙+砂紙 製作成簡易打磨設備,處理鋁條切面太銳利的地方
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09184_zpsa6jepidy.jpg
然後試組,拿待廢棄的光碟機定位出5.25"擴充槽的鎖孔
還有備用的白牌電源供應器模擬鋁片擺設位置
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09190_zps7dyrogcw.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09202_zpsox2f7sto.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09207_zpsh36oww3k.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09246_zpskwxnf656.jpg
主機板到貨前,先來試組開關面板
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/cherry_zpsmktxm8db.png
這邊用兩顆Cherry綠軸作為 Reset/開機按鈕
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09122_zpstxmvafvk.jpg
後面會再加上LED作為 硬碟/POWER 指示燈
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09230_zpskohor0tq.jpg
EVGA X99 FTW K 主機板準備上機
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09303_zpswpjdgzkl.jpg
定位主機板銅柱很麻煩,因為螺絲全部都藏在主機板底下
必須移除主機板才能調整,還要兼顧10個孔位的相互位置
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09449_zps7msg5mjn.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09437_zps0iqxazui.jpg
調整過程中損壞好幾顆止付螺絲,後來乾脆全部螺絲換成304不鏽鋼材質
可以看到螺絲頭從黑色變成銀色的,總數約150顆通通重來....
介面卡的固定也用橢圓片
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09421_zpsvpbo6gfa.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09434_zpsn7qp49qz.jpg
實際組裝後發現,橢圓片會隨著螺絲鎖緊被拖著改變角度
一邊校正角度一邊鎖緊螺絲變成非常困難的任務,根本是整人的設計
所有硬碟皆以抽取匣安裝,不然事後再調整橢圓片也是個惡夢
這邊採用兩個2.5"+3.5"+USB 3.0 x2的綜合擴充面板
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09521_zpsmqyylbvo.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09525_zpsmzk8k6gh.jpg
光碟機預留空位
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09529_zpsrkensz3x.jpg
傳統機殼的前置USB2.0與音效插孔
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09531_zpsnkq2rhz4.jpg
安裝鋁合金腳墊,螺絲是M6規格,但鋁條廠商忘記攻牙
我本來買了攻牙器但使用時斷在洞裡,只好重新訂製攻牙的鋁柱
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09535_zpsghq3mysk.jpg
同樣是訂製的OEM高度R4鍵帽也一併到貨了
大SSD時代,機殼標示也要進化
但是因為這兩顆鍵帽表面塗層有刮痕,跟賣家反應後獲得全額退費
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09538_zps8bccybr9.jpg
主要零件試組
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09609_zpshsvsimvx.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09612_zpsfzutbuoz.jpg
才裝好沒多久的5.25區又全部拆掉往左移一格
Amphenol反彎頭SATA線拉5條,預留一個給未來裝光碟機時使用
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09737_zpsc9usev2o.jpg
用長耳夾固定懸空的各種線
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09734_zpspjgxhduj.jpg
後來因為選購長度30cm的顯示卡,顯示卡後端會突出機殼
必須重新調整主機板位置,最累的10顆螺絲全部重來.........
示範顯示卡是大跳水的ASUS STRIX-R9FURY-DC3-4G-GAMING
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09620_zpsvz1famn0.jpg
重新調好主機板跟顯卡之後要挑塔型散熱器
先裝上CPU , Broadwell-E 6850K 體積滿大的
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09640_zpsl1owjblg.jpg
約有18cm的空間
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09657_zps7zqe1v1c.jpg
Cryorig網站提供紙模型下載列印功能相當貼心,可惜也都不合用
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09697_zpsdkl2wkgv.jpg
再比對過幾家號稱不卡PCIe的塔散後發現,EVGA預留的空間真的比較小
別家主機板可以用的散熱器,在EVGA X99系列都不能用
最後我是買SilverArrow IB-E Extreme,然後自己DIY修剪鰭片
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09782_zpsxaw6g9ch.jpg
CPU處理完換硬碟,這邊採用OCZ RD400 256G
另外貼了散熱片
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09835_zpsolq8jwse.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09838_zpszwqtxl7t.jpg
再補上記憶體,終於全部零件都裝上可以開機了
搶在7/29微軟免費升級Win10的最後關頭解除成就
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09788_V2_zpsf5hbpaz2.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09791_zpsb2rknzrf.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09794_zpscmu7egwz.jpg
接著要在機殼上裝螢幕
直接使用New iPad的液晶+HDMI2EDP轉接板,規格2048x1536 40Hz
https://www.youtube.com/watch?v=M-dQQNXC6CI
排線轉板
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09875_zpswc3vjcfh.jpg
HDMI轉板
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09878_zpsfuuiodar.jpg
自己再設計一個三層式的外殼
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/SC_zpsgiquolgw.png
組合！
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09983_zpsk3zsmoad.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09993_zps9sjimhli.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09997_zps3sowoltb.jpg
後來發現風扇有點吵
倒不是說滾珠軸承的噪音多大,但難免輸新品的油封軸承
拆下泡油也沒改善多少乾脆買新的來換
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09811_zpsrsfe2oim.jpg
NSK ISC 3x8x4培林換完略有改善,但效果有限
反正運轉噪音大部分時間會被風切聲蓋掉,就算了吧
裝到一半發現原本設計的介面卡固定方式不適合顯示卡
不只會歪斜,還有前後高低不平的問題
可以看見顯卡導熱管已經低過SATA座頂端,正常的電腦機殼不應該發生這個現象
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09715_zpshincu04m.jpg
所以另外訂了背板來裝,支撐柱就拿之前攻牙斷頭的鋁柱切短使用
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09912_zpsii0sejof.jpg
大致定位完之後製作開關線路,焊接完把線扭成麻花然後火烤定型
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09940_zps5mrsqi1x.jpg
再使用長耳夾固定,長耳夾對只有框架的機殼來說簡直是走線神器
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09919_zpsn8gry8o9.jpg
接著上濾網,這邊採用PVC沖孔網(孔徑1.0mm)
底部露出螺絲頭,在濾網對應的位置切出孔位穿過固定
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC09907_zpsaimj4xov.jpg
效果差強人意,密合度不佳,未來應該加上外框固定效果會比較好
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10011_zpsv84vix6i.jpg
CPU風扇也加濾網
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10014_zpsrbhejmjk.jpg
前面接好燈號之後我發現M.2介面NVMe SSD在存取時並不會觸發指示燈
後來直接換有燈號針腳的轉接卡
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10216_zpsggkywjtc.jpg
內部組裝大致完成,開始接洽訂製透明外板,首先是左右的壓克力
由於尺寸較小,後方開風扇孔造型較複雜等多種理由,無法製作強化玻璃
不想使用未強化的玻璃材質所以改用透黑壓克力代替,效果依然不錯
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10047_zpshj7cndjo.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10060_zps0o7pkril.jpg
上桌試擺,還需要調整電腦喇叭,螢幕支架位置,高度等
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10051_zpsttryim2g.jpg
之前不知道從哪裡拆來的遙控車天線
改裝成滑鼠線架非常好用,好用到會流淚的程度
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10057_zps3wkofzjq.jpg
然後玻璃頂板也做好了,試裝效果非~~~常的好
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10124_zps2ollpyrt.jpg
電腦組裝原本應該在此告一段落,但用一陣子之後發現跑遊戲的效能非常差
不斷反覆測試仍找不到問題,決定先把快滿月的ASUS Fury拿去退貨,換MSI RX480 8G
約1周之後才發現是主機板問題,記憶體插到某槽就會降速,一樣也送RMA換新
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10181_zpsntlfohhm.jpg
MSI RX480 8G依然退貨處理,買前沒注意到輸出接頭設計成2HDMI+2DP
不合我需求的1HDMI+3DP,最後換成PowerColor AXRX 480 8GBD5-3DH/OC
順便裝官方解鎖BIOS,再也沒出現問題
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10226_zpsykdlhtvy.jpg
Reset按鍵少用所以沒有插在正確位置防誤觸(紫色),僅連接SSD燈號(黃色)
整體配置,後進氣扇是TY-143 SQ,殼內轉90度再擺一顆
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10234_zpsjvwfm3fl.jpg
顯卡背板緊貼塔散
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10227_zpszpgl9bg0.jpg
未使用的PCI-E插槽拿主機板撕下的貼紙貼起來防塵
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10242_zpstlzpibzx.jpg
然後繼續處理螢幕,我選的螢幕是三台acer XZ271
VA 曲面1800R 1920x1080 144Hz Freesync
但我事先買好的螢幕支架高度不足,螢幕的鎖點也偏高
造成螢幕高度偏低,電腦塞不進螢幕底下
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10128_zpsqdb0uz8n.jpg
只好再訂製三片不鏽鋼轉接板,但廠商沒打洞就寄給我.....
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/IMAG0166_zpsskfberhy.jpg
重作重寄
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10132_zpsrbtkssl6.jpg
螢幕整體高度提升10cm
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10138_zpslwr5hfsw.jpg
剛好碰到缺貨,等了一陣子才湊齊三台
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10147_zpsnarys2z2.jpg
終於,再難裝的電腦還是有組完的一天 (桌布是老婆畫的)
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10447_zps2qvdgbgs.jpg
前面板
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10302_zpsfurdqomh.jpg
後來發現IDE光碟機竟然還沒壞,從內部轉USB繼續用
Rainmeter可以顯示很多資訊,很多漂亮的面板可以套用的桌面美化軟體
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC10325_zpsrfgiilgb.jpg
開機按鍵最終定案
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC00493_zpsn2tnzgmf.jpg
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC00499_zpsv27qio3s.jpg
同位置下方有另一組主機板的同功能按鍵跟燈號
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC00513_zpsxtkkrpk7.jpg
HDD的燈號會在Reset以及抽取匣顯示
多一台螢幕的用途真的很廣泛(我本來電腦就是三螢幕)
實況三螢幕遊戲之類的還是可以擺聊天視窗或實況軟體監控
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC00507_zpsqefheeyp.jpg
旁邊再架個Mic,超完美
http://i1244.photobucket.com/albums/gg569/knucklesleee/2016-07%20DIY%20PC/DSC00468_PS_zps9bmnkb76.jpg